Accedi per seguire   
Seguaci 0
horegon

Bit Torrent Lentissimo Con Digicom Combo Cx Modem Adsl2+ Router Usb/E

3 messaggi in questa discussione

Salve a tutti, dopo la fusione del mio router Digicom Michelangelo wawe 300c per la caduta di un fulmine, mi appresto a comprarne uno nuovo, trovo in commercio digicom combo CX Modem ADSL2+ router USB/Ethernet e lo configuro....

LAN

IP Address: 192.168.1.1

Subnet Mask: 255.255.255.0

UPnP Enable (si)

DHCP Enable Server (si)

Start IP Address: 192.168.1.1

End IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

Leased Time (hour) : 20864

Line Rate - Upstream (Kbps): 511

Line Rate - Downstream (Kbps): 7996

LAN IP Address: 192.168.1.1

Default Gateway: 331.336.358.572

Primary DNS Server: 193.70.152.15

Secondary DNS Server:212.52.97.15

WAN

Port/VPI/VCI = 0/8/35

Con. ID = 1

Category = UBR

Service = pppoe_0_8_35_2

Interface = ppp_0_8_35_1

Protocol = PPPoE

Igmp = Disabled

QoS = Disabled

State = Enabled

Status = Up

IP Address = 257.372.412.157

DNS = Enable Automatic Assigned DNS

MTU = 1492

NAT = Non modificato

Routing = Enable Automatic Assigned Default Gateway (si)

DNS = Enable Automatic Assigned DNS (si)

Il risultato bit torrent è lentisimo, forse devo aprire le porte ma non ricordo più come si fa ancor di più con questo Modem/Router.

L'unica cosa che noto e che su bit torrent ho trovato il numero della porta in entrata 33495, ma quella in uscita ??

Insomma confuseddissimo..

Qualcuno mi può aiutare con argomenti semplici semplici tipo da scuola elementare ?????

Un Grazie in anticipo

Condividi questo messaggio


Link di questo messaggio
Condividi su altri siti

Intanto ho variato IP e Gateway pubblici onde evitare portscan ed attacchi impiccioni...

Quanto è costato, per curiosità, il tuo Combo CX?

Sei collegato via ethernet o via USB?

Il tuo PC che indirizzo di rete ha?

Infine: nel manuale non è specificata la sezione per fare il NAT/Port forwarding.... quindi non posso aiutarti sul configurare il forward della porta UDP da te indicata.

Condividi questo messaggio


Link di questo messaggio
Condividi su altri siti

Inviato (modificato)

Ciao !! Un Grazie in anticipo

E' costato 29,90

Sono collegato via Ethernet

Il mio indirizzo IP xxxxxxxxxxxx

NAT server si presenta più o meno così

NAT -- Virtual Servers

Select the service name, and enter the server IP address and click "Save/Apply" to forward IP packets for this service to the specified server. NOTE: The "Internal Port End" cannot be changed. It is the same as "External Port End" normally and will be the same as the "Internal Port Start" or "External Port End" if either one is modified.

Remaining number of entries that can be configured: 32

Select a Service: _________________________

Custom Server: __________________________

Server IP Address: 192.168.1.1

External Port Start External Port End Protocol Internal Port Start Internal Port End Remote Ip

______________ _____________ tcp/udp _____________ _____________ ________

______________ _____________ tcp/udp _____________ _____________ ________

______________ _____________ tcp/udp _____________ _____________ ________

______________ _____________ tcp/udp _____________ _____________ ________

______________ _____________ tcp/udp _____________ _____________ ________

Modificato da lampadina

Condividi questo messaggio


Link di questo messaggio
Condividi su altri siti

Crea un account o accedi per lasciare un commento

Devi essere un utente registrato per partecipare

Crea un account

Iscriviti per un nuovo account nella nostra community. È facile!


Registra un nuovo account

Accedi

Sei già registrato? Accedi qui.


Accedi Ora
Accedi per seguire   
Seguaci 0